How to Use Head Gasket Sealer: Flush, Pour, Run, Cure
Ready to repair it?
How to use head gasket sealer the right way
To use head gasket sealer, confirm it really is the head gasket, flush the antifreeze out with plain water, pour the sealer in and run the engine exactly as the instructions say. With Thermalweld that means about 10 minutes in the lowest gear at 3,000 rpm, then driving normally at least four times in the first three days so the seal cures.
The steps matter as much as the bottle, so here they are in order. No need to remove the thermostat.
Before you pour anything in
Three checks come first.
- Is it the head gasket? Do a block test. Most auto parts stores lend the tester, and the fluid costs about $10. See how to tell if your head gasket is blown.
- What caused it? Most blown head gaskets start with a cooling system part that failed first: a stuck thermostat, a weak water pump, a clogged radiator, a fan that does not come on, or a cap that lets the pressure out. Fix that part, or the new seal usually goes the same way.
- Does it start and run? The repair works from inside the cooling system while the engine runs, so the engine has to start and run for at least 15 minutes. If it will not start, call us before you buy anything.
If the oil cap is milky, check the dipstick. At the full mark or an inch or two over, change the oil after the repair. Five inches or more over can point to a cracked block, so call first. See milky oil under the oil cap.
What you need
- The Thermalweld kit made for your engine: gas, hybrid, Cadillac Northstar or diesel. See the kits.
- Plain water, enough to fill the cooling system several times.
- A container to catch the old coolant.
Step 1: flush the antifreeze out with plain water
Thermalweld does not mix with antifreeze, so the antifreeze comes out first. This is the hardest part of the job. Dave Whitmer, our field technician, does it as a flush and fill:
- With the engine cold, take the pressure cap off.
- Open the drain valve at the bottom of the radiator, called the petcock, and catch the coolant in a container.
- Close it, fill the system with plain water and put the cap back on.
- Run the engine up to operating temperature with the heater on, so water flows through the heater core too. When the upper radiator hose is hot, the thermostat has opened and the water is moving through everything.
- Let it cool for at least 45 minutes before you open the cap, then drain it again.
- Repeat until the system has been filled four times. On the last fill, leave room for the bottle.
Not comfortable doing it yourself? Ask any repair shop to flush the cooling system with plain water only. In Dave’s experience a shop can do that in under an hour.
Step 2: pour in the Thermalweld
With the engine cool, pour the bottle into the radiator, or the expansion tank on systems that fill there, and put the cap back on.
Step 3: run it
Shift into the lowest gear and run the engine at 3,000 rpm for about 10 minutes. It usually takes less than 10 minutes to seal the head gasket.
Watch the temperature gauge the whole time. If it climbs toward hot, shut the engine off and call us.
Step 4: let it cool, then top up
Let the engine cool down completely, then slowly remove the pressure cap and add plain water to replace what was lost. Never open the cap on a hot engine.
Step 5: let it cure
The head gasket is sealed now, but not fully cured. Drive normally at least four times in the first three days. The more times the engine comes up to operating temperature, the better.
Step 6: flush again and go back to antifreeze
Once the cure is done, flush the treatment out with plain water the same way, heater core included, then refill with antifreeze. If the oil was milky, change the oil too.
On a diesel
Diesels follow a longer routine: after the plain water flush, rounds of idling and cooling, then a short drive in a lower gear. Follow the diesel steps in the easy repair instructions, and call (844) 796 7968 before you start so we can go through them with you.
The mistakes that make a sealer fail
- Pouring Thermalweld into antifreeze instead of plain water.
- Sealing the gasket and leaving the part that caused it in the car.
- Waiting until the engine no longer starts. Every mile makes the breach bigger. See can you drive with a blown head gasket.
Already tried a sealer that did not work?
Where other products failed, we help you fix it. Before you pour anything else in, call and tell us what went in, how it was used and what the engine is doing now.
Free unlimited tech support from the people who make it
We are the experts in cooling systems: we find what caused the failure, not only fix the gasket. Call (844) 796 7968 at any step, flush to cure. You talk to the people who make Thermalweld, as often as you need, free. Nobody else in the industry offers that. Thermalweld is BBB accredited and A+ rated, and our field technician, Dave Whitmer, has more than 1,100 blown head gasket repairs, and growing.
We are saving livelihoods one blown head gasket at a time.
For mechanics and repair shops
You know the flush is where the time goes. Do it right, follow the steps, and the head stays on. Your customer keeps the car, you keep the job, and our tech support is on the phone whenever the job gets tough. Unheard of in the industry. Nobody else comes close.
Mechanics: your first bottle is free. So is the unlimited tech support. thermalweld.com/technicians
Need a mobile mechanic? We find one for you.
Call (844) 796 7968 and tell us where the car is. At our cost, we call mobile mechanics in your area, qualify a well reviewed one for your job, and back them with free, unlimited tech support from start to finish. We know of no other head gasket brand that does this. How we find your mechanic
Quick answers
Do you have to flush before using head gasket sealer?
With Thermalweld, yes. It does not mix with antifreeze, so the cooling system is flushed with plain water first, heater core included. A shop can do the flush for you.
Where do you put head gasket sealer?
Into the radiator, or into the expansion tank on systems that fill there, with the engine cool. On a diesel it goes into the surge tank or the radiator.
How long do you run the engine after adding head gasket sealer?
On a gas engine, about 10 minutes in the lowest gear at 3,000 rpm. Then let it cool, top up with plain water, and drive normally at least four times in the first three days so the seal cures.
Do I need to remove the thermostat?
No. The Thermalweld instructions do not call for removing the thermostat.
When do I put antifreeze back in?
After the cure. Flush the treatment out with plain water, heater core included, then refill with antifreeze. If there was coolant in the oil, change the oil as well.
More answers
- Easy repair instructions
- How to tell if your head gasket is blown
- Blown head gasket symptoms
- Can a blown head gasket be fixed without replacing it?
- Can you drive with a blown head gasket?
- Head gasket repair cost
This page is a guide, not a diagnosis. Call (844) 796 7968 with your engine, mileage and symptoms.
