Can a Mobile Mechanic Fix a Head Gasket? Often, Here Is How

Should I fix it?

Can a mobile mechanic fix a head gasket?

Often, yes, right in your driveway: a mobile mechanic can usually repair a blown head gasket with a chemical repair like Thermalweld, with no tow and no teardown, as long as the engine still starts and runs. Replacing the gasket is a different job, and most mobile mechanics, like many shops, will not take it on.

Two ways to fix a blown head gasket

Replace it. The top of the engine comes apart, the cylinder head comes off, a new gasket goes on and everything goes back together. A shop charges $2,000 to $7,000 for that, depending on the engine. Many shops will not quote it at all; they say they do not do head gaskets and offer to replace the engine. Most mobile mechanics leave this job alone too.

Seal it from the inside. A chemical repair works through the cooling system while the engine runs. No parts come off. What it needs is plain water, a container for the old coolant, the kit made for the engine, and an engine that still starts and runs. That is why it fits a driveway. Dave Whitmer, our field technician, has repaired more than 1,100 blown head gaskets in customers’ driveways, and growing.

What a driveway repair looks like

The repair follows the published Easy repair instructions. In short:

  1. Test first. A block test shows whether combustion gas is getting into the coolant. Most auto parts stores lend the tester, and the fluid costs about $10. See how to tell if your head gasket is blown.
  2. Find what caused it. Most head gaskets blow because a cooling system part failed first: a stuck thermostat, a weak water pump, a clogged radiator, a fan that does not come on, or a pressure cap that lets the pressure out. That part gets fixed too.
  3. Flush with plain water. Thermalweld does not mix with antifreeze, so the antifreeze comes out first, heater core included. Drain, fill with water, run it to temperature with the heater on, let it cool at least 45 minutes, drain again. Four fills in all. This is the longest part of the job.
  4. Pour it in and run it exactly as the instructions say for that engine.
  5. Let it cure. The car goes back to its owner, who drives normally at least four times in the first three days so the engine comes up to operating temperature.
  6. Flush again, then antifreeze. Once the cure is done, the treatment is flushed out with plain water and the system is refilled with antifreeze.

On an engine that is a good fit, the time in the driveway is measured in hours, not days. In Dave’s words: “we can repair a Toyota in about an hour to an hour and a half.” A diesel takes longer, with rounds of idling and cooling before a short drive in a lower gear, so call before you start on one.

When the driveway repair is off the table

A good mobile mechanic will say no to some engines.

  • It will not start, or will not turn over. The repair works while the engine runs, so it has to start and run for at least 15 minutes. If it will not turn over at all, it may be hydrolocked. Do not keep cranking it.
  • The dipstick reads five inches or more over the full mark. That much coolant in the oil can point to a cracked block. Call us before anything goes in. At the full mark or an inch or two over, the oil simply gets changed after the repair. See milky oil under the oil cap.
  • It keeps overheating and nobody knows why. Fix the cooling system part first, or the new seal usually goes the same way as the old gasket.

Questions to ask a mobile mechanic before the job

  1. Did you test it? A block test or a compression test, not a guess.
  2. What caused it, and will you check the thermostat, water pump, radiator, fan and cap?
  3. Will you flush with plain water, heater core included, before anything goes in?
  4. What happens if the engine will not start or the dipstick reads high?
  5. Will you call the maker’s tech support if the job gets tough? With Thermalweld, that call is free, and you talk to the people who make it.

Already tried a sealer that did not work?

Where other products failed, we help you fix it. Before anything else goes in, have your mechanic call us and tell us what was used, how it went in and what the engine is doing now.

The experts in cooling systems, free on the phone

We are the experts in cooling systems: we find what caused the failure, not only fix the gasket. Drivers and mechanics can call (844) 796 7968 at any step, as often as they need, and talk to the people who make Thermalweld. Free, unlimited tech support. Nobody else in the industry offers that. Thermalweld is BBB accredited and A+ rated.

We are saving livelihoods one blown head gasket at a time.

For mobile mechanics and repair shops

The blown head gasket is the job most mechanics send away, and the customer often loses the car with it. With Thermalweld on the truck it becomes a driveway job: test, find the cause, flush, treat, and our tech support is on the phone whenever the job gets tough. Your customer keeps the car. You keep the customer. Unheard of in the industry. Nobody else comes close.

Mechanics: your first bottle is free. So is the unlimited tech support. thermalweld.com/technicians

Need a mobile mechanic? We find one for you.

Call (844) 796 7968 and tell us where the car is. At our cost, we call mobile mechanics in your area, qualify a well reviewed one for your job, and back them with free, unlimited tech support from start to finish. We know of no other head gasket brand that does this. How we find your mechanic

Quick answers

Can a mobile mechanic fix a head gasket?

Often, yes. A chemical repair needs no teardown, so a mobile mechanic can do it in a driveway on an engine that still starts and runs. The cooling system is flushed with plain water first, and the part that caused the failure gets fixed too.

Can a mobile mechanic replace a head gasket?

Some can, but most will not take the job on, and many shops will not either. Replacing the gasket means taking the cylinder head off, and a shop charges $2,000 to $7,000 for it. A chemical repair is the head gasket job that fits a driveway.

How long does a mobile head gasket repair take?

On an engine that is a good fit, hours, not days. Our field technician repairs a Toyota in about an hour to an hour and a half. The flush takes most of that time, and the seal finishes curing over the next three days of normal driving.

How does a mechanic check for a blown head gasket?

Usually with a block test, which checks the coolant for combustion gas, or a compression test. A good mechanic also asks about coolant loss, white smoke from the tail pipe, coolant in the oil and rough running. A diagnosis made without a test deserves a second look.

Can my mechanic call Thermalweld for help?

Yes. Tech support is free and unlimited, for drivers and mechanics alike, from the people who make Thermalweld: (844) 796 7968. Mechanics who register at thermalweld.com/technicians also get their first bottle free.

More answers

This page is a guide, not a diagnosis. Call (844) 796 7968 with your engine, mileage and symptoms.