Can a Blown Head Gasket Cause Pressure in Cooling System?

Is it my head gasket?

Can a blown head gasket cause pressure in the cooling system?

Yes. A breached head gasket lets the pistons push combustion gas into the cooling system, and that gas builds pressure heat did not make: a hard upper radiator hose on a cold engine, coolant pushed out of the reservoir, bubbles in the tank. A cap, a stuck thermostat or trapped air can build pressure too, and a few simple checks tell you which you have.

We are the experts in cooling systems. We find what caused the failure, not only fix the gasket.

Safety first. Never open the radiator cap or the pressure cap until the engine has cooled completely.

Why a blown head gasket pressurizes the cooling system

The pistons push 100 to 200 psi or more against the head gasket on every stroke. The cooling system is built to hold only the pressure on its cap, a small fraction of that. Once the gasket is breached between a cylinder and a coolant passage, combustion gas is forced into the coolant and the pressure climbs.

When the engine is off and cooling, coolant can also seep the other way, into the cylinder. That is how one breach can pressurize the system and still lose coolant out the tail pipe as steam.

Signs the pressure is combustion gas

  • The upper radiator hose is rock hard on an engine that has sat cold for a couple of hours or overnight.
  • The hose turns hard soon after a cold start, long before the engine is warm.
  • Coolant is pushed out of the reservoir or the overflow, and the level keeps dropping.
  • Bubbles rise in the reservoir with the engine running, most of all right after a cold start.
  • You keep adding coolant. A blown head gasket always loses coolant, often as a mist out the tail pipe that you never see.

Pressure that is normal

Some pressure belongs there. Heat raises it, and the system holds it so the coolant does not boil: water boils at 212 degrees F, and at about 250 degrees F under pressure. The cap lets anything over its rating out into the reservoir. A firm upper hose on a hot engine is expected. After a couple of hours cooling, the pressure should be gone and the hose should squeeze soft.

Other things that build pressure or push coolant out

  • A part that lets the engine run hot. A thermostat stuck closed, a clogged radiator, a worn water pump or a fan that does not come on lets the coolant boil, and the steam pushes coolant into the reservoir.
  • Trapped air. After a coolant change or a flush, air pockets can form hot spots that boil first.
  • A cap that no longer holds. A worn seal or a weak spring lets the pressure go early, the boiling point drops, and the coolant can boil over.

These build pressure from heat, so they show up once the engine is hot. Combustion gas builds it on a cold engine too.

Three checks, cheapest first

  1. Squeeze the upper hose cold. After the engine has sat a couple of hours, soft is normal. Rock hard points to combustion gas.
  2. Block test, engine running. It checks for combustion gas in the coolant. Most auto parts stores lend the tester and the fluid costs about $10; a shop charges around $35 to $50. Do not rev hard while testing; splashed coolant can give a false reading. Dave Whitmer, our field technician, shows how: How to do a block test.
  3. Pressure test the system and the cap, engine cold. A hand pump brings the system up to the pressure on the cap, never higher. A drop with a drip is an outside leak. A drop with no drip anywhere points to coolant going inside the engine. A cap tester checks the seal and the spring.

The pressure test finds leaks; the block test looks for combustion gas. Do both before you blame or clear the head gasket. More on how to tell if your head gasket is blown.

Can the pressure overheat the engine?

Gas in the coolant does not, by itself, make an engine run hot. A blown head gasket overheats an engine in two cases: an air pocket forms around the thermostat so it never opens, or coolant is pushed out or leaves as steam and the level drops. Low coolant overheats any engine. If the gauge climbs, pull over and shut it off.

When it is the head gasket

While the engine still starts and runs, a blown head gasket can be sealed with the head on. Thermalweld seals the breach from inside the cooling system while the engine runs. It does not mix with antifreeze, so the system is flushed with plain water first, heater core included. Every step is in the easy repair instructions. More on whether a blown head gasket can be fixed without replacing it.

Find the cause too. Most head gaskets blow because a cooling system part failed first: a stuck thermostat, a weak water pump, a clogged radiator, a fan that does not come on. If it overheated and you never found out why, you may have two problems.

Free unlimited tech support from the people who make it

Hose hard on a cold engine, or coolant pushing out of the tank? Call (844) 796 7968 with the engine, the mileage and how much coolant you add. You talk to the people who make Thermalweld, as often as you need, free. Nobody else in the industry offers that. Where other products failed, we help you fix it. Thermalweld is BBB accredited and A+ rated.

We are saving livelihoods one blown head gasket at a time.

For mechanics and repair shops

Squeeze the upper hose before the first start, block test it running, then pressure test the system and cap. Pressure on a cold engine points inside; pressure only when hot points to the cap, thermostat, radiator, pump or air. On a diesel, a positive block test can mean the EGR cooler as well as the head gasket. Our tech support is on the phone whenever the job gets tough. Unheard of in the industry. Nobody else comes close.

Mechanics: your first bottle is free. So is the unlimited tech support. thermalweld.com/technicians

Need a mobile mechanic? We find one for you.

Call (844) 796 7968 and tell us where the car is. At our cost, we call mobile mechanics in your area, qualify a well reviewed one for your job, and back them with free, unlimited tech support from start to finish. We know of no other head gasket brand that does this. How we find your mechanic

Quick answers

Can a blown head gasket cause pressure in the cooling system?

Yes. A breached gasket lets the pistons push combustion gas into the coolant. Look for a hard upper hose on a cold engine, coolant pushed out of the reservoir and bubbles in the tank.

Why is my cooling system pressurized when the engine is cold?

Normal pressure comes from heat, so it should be gone after a couple of hours cooling. A hose that stays hard cold points to combustion gas from a blown head gasket. Do a block test.

Why is coolant coming out of the reservoir?

Combustion gas from a blown head gasket can push it out. So can coolant boiling from a stuck thermostat, a clogged radiator, a worn pump, trapped air or a weak cap. If the engine is not overheating, test for combustion gas first.

Will a coolant pressure test show a blown head gasket?

It can point to one: a drop with no drip points to coolant going inside the engine. The block test checks for combustion gas, so do both.

Should the upper radiator hose be hard?

Firm on a hot engine, yes. Rock hard on an engine that has sat cold for hours, no. That points to combustion gas.

More answers

This page is a guide, not a diagnosis. Call (844) 796 7968 with your engine, mileage and symptoms.